Sullair Mark II w/TEI Jaws,HEK Remote Winch,Joy VCR360/361

Used for Overburden Drilling applications.

DLT# AT9214

Sullair Mark II Specifications and Dimensions
General (English/Metric)
Net Weight	Minimum Height	Width	Length w/o Feed	Feed Vertical	Feed Horizontal	Ground Clearance
13800 lbs/6260kg	4'8"/1420 mm	8'/2440 mm	16'3"/4955 mm	16'8"/5080 mm	22'5"/6835 mm	12"/305 mm
Tow Hitch Height
1'8"/510 mm
Boom (English/Metric)
Extension	Swing Left	Swing Right	Elevation Up	Elevation Down	Highest Horiz. Hole	Lowest Horiz. Hole
5'/1525 mm	37°	40°	39°	10°	16'/4675 mm	3'/915 mm
Max. Reach Left	Max. Reach Right
11'8"/3555 mm	13'8.5"/4180 mm
Feed (English/Metric)
Dump	Swing Left	Swing Right	Extension	Motor Power	Chain Pull	Chain Speed
160°	40°	40°	4'/1220 mm	5.6 hp/4.18 kW	3500 lbs/1590 kg	104 ft/min / 31.7 m/min
Chain Pitch	Drill Rod Change	Drill Travel
1.25"/31.75 mm	12'/3660 mm	14'6"/4420 mm
Tracks (English/Metric)
Width of Pads	Ground Contact Length	Area	No. of Bottom Rollers	No. of Top Rollers	Front Idler Adjustment	Tram Motor Power
10"/255 mm	7'/2135 mm	1680 sq. in./10840 sq. cm.	7	1	Hydraulic (grease gun)	15 hp/11.2 kW
Tractive Effort	Tram Speed	Transmission	Clutch	Final Drive	Brake
13212 lbs./5990 kg	158 ft/min / 48 m/min	Planetary	Splined Sleeve	Spur gear, enclosed	Band, auto spring set, air released

Continuous Rotation Drills
VCR-360

Improved Production Efficiency with Reduced Energy Consumption

The Most Advanced Drills in the VCR Series
Designed for High Penetration, Stength and Reliability
Delivers High-Performance Using Less Air, Less Fuel

More Performance on Less Air

VCR-360, 600 cfm/air

Sealed Lubrication System Extends Drill Life

The Entire Rotation Assembly is Lubed By Its Own System Sealed Off From the Percussion Assembly and Outside Environment
The Air is Provided Separately to the Dill String

Exclusive SULLIVAN Valveless, Continuous Rotation Design

The Piston is the Only Moving Part in the Hammer
Consistently Faster Penetration
Independently-Powered Rotation with an Efficient Gear-Type Air Motor
Infinitely Variable Rotation Rates
Low Maintenance

Quiet Muffler w/Air and Noise Directed Away From Operator

Specifications for VCR-360
Bore Diameter	5-1/4" (134 m)
Stroke	3-5/8" (92 mm)
Striking Bar	Threaded for optional steel.
Drill Steel	1-1/2" OD Std., 1-3/4" OD Opt.
Rotation Type	Independent
Hose Size	2" Drill, 1" Flushing
Hole Size Range	2-1/2" - 4" (64 - 102 mm)
Air Pressure	100 psi (7 kg/cm²)
Air Requirements	600 cfm (16.8 m³/min) Drill & Blow (up to 2500 ft. above mean sea level)
Drill Weight	496 lbs. (225 kg)

Diagram for VCR-360

Sullivan Continuous Rotation Drill
VCR - 361

Improved Production Efficiency with Reduced Energy Consumption VCR-361

    The new VCR-361 drill represents the newest and most advanced drill in popular VCR series of high performance Sullivan drill engines. Based on the same design concepts that have made the VCR-261 drills the leasers in their class for penetration, strength and reliable service, the VCR-361 drill incorporates innovations that make it one of the most energy efficient drills available. That is, it gives you the same high performance of the VCR-261 drills while using less air and fuel...something that's certainly right for these energy costly times.

More Performance On Less Air
    With the new VCR-361 drill you need only 850 cfm of air to drill at the same penetration rate as the VCR-261 drill (which requires 1000 cfm). The savings are obvious the initial cost economy of a smaller air compressor is considerable, plus the fuel consumption of the smaller compressor is significantly less. Or, if a dry dust collector is desired (or required), the VCR-361 drill will operate at peak efficiency with dust collection off the same compressor that powered the VCR-261 drill alone.

Lubrication System Extends Drill Life
    The new VCR-361 incorporates a sealed lubrication system which extends drill engine life. The entire rotation drive assembly is lubricated by its own system, sealed from the percussion assembly and the outside environment. Blow air is provided separately to the drill string.

Exclusive Sullivan Valveless, Continuous Rotation Design
    Like previous Sullivan drill engines, the new VCR-361 has only one moving part in the hammer - the piston. This valveless design has proven itself with penetration rates that are consistently faster than conventional designs. Rotation is independently powered by an efficient gear-type air motor. Rate of rotation is infinitely variable to suit drilling conditions.

Quieter Muffler
    A resiliently mounted heavy-walled alumninum muffler substantially reduces noise. Spent air (and noise) is directed up and away from the operator further increasing operator comfort.

VCR-361 Drill Operation The two basic operation functions of the VCR-361 drill - percussion and rotation - are accomplished independent of each other.
Percussion	Rotation
Air entering the drill passes directly to both ends of the piston. The piston reciprocates in the cylinder in a valveless cycle in which the piston itself operates as a valve, alternately exposing and covering ports on the ends of the cylinder. This is a volume expansion controlled cycle using only one moving part - the piston.	A separate air inlet admits air to a gear-type air motor. The air motor transmits torque through the rotation gearing to the chuck driver which is splined to receive the striking bar. Rotation (rpm) of the drill steel is continuously variable by use of the rotation valve on the drill feed.

VCR-361 Drill Specifications
Bore Diameter	6-1/2" (166 mm)
Stroke	3-3/4" (95 mm)
Striking Bar	Threaded for optional steel
Drill Steel	1-3/4" O.D.
Rotation Type	Independent
Hose Size	2" Drill, 1" Blow
Hole Size Range	3" to 4" bit dia. (76 - 102 mm)
Air Pressure	100 psi (7 kg/cm^₂)
Air Requirements	850 cm (24 m^₃/min) Drill & Blow (up to 2500 ft. aboce mean sea level)
Drill Weight	496 lbs. (225 kg)